Laying Out Square Corners

 
For crisp, neat beds and borders, perfectly square corners are a must -- and a sign of good workmanship. This simple technique assures you of flawlessly square corners every time.
 

Lay out one edge of the bed and drive in a stake where you want the corner. Lay out the second edge with batterboards and stretch a mason's line between them across the corner stake.

 

With a tape measure, check that the corner is square by making a 3-4-5 triangle. Adjust the mason's line as needed until the distance between two points 3 feet and 4 feet from the corner stake is exactly 5 feet.

 

Mark the endpoints with tape and transfer them to the ground with a plumb bob. Drive in stakes to mark the endpoints and stretch a mason's line along the ground between them. Sprinkle powdered chalk over the line to mark the rough outline of the bed.

 
   
 

RELATED PROJECTS


Laying Out Arcs
 

Laying Out Straight Edges
 

Laying Out Free-form Curves

 
 

Do it Yourself Projects


Aligning the Bolt and Strike Plate

Adjusting an Out-of-Balance Door

Adding a Telephone Extension

Building a Multilevel Deck

Building a Ground-Level Deck

Building a Single-Level Raised Deck

Building a Low-Level Deck

Building a Closet Organizer

Building Utility Shelves

Constructing a Built-In Shelving Unit

Freeing a Sticking Door

Framing a Prehung Interior Door

Fixing Leaky Sink Strainers

Finishing Inside Corners

Finishing Outside Corners

Grouting

Getting Ready to Paint

Hanging Borders

Installing Cabinet Drawer Fronts

Installing Cabinet Doors

Installing a Security Lock

Installing an Entry Door

Installing Split-Jamb Interior Doors

Installing a Cable TV Jack

Installing Coaxial TV Cable

Installing a Programmable Thermostat

Installing a Ceiling Fan

Installing a Dimmer Switch

Installing a Three-Way Switch

Installing Specialty Switches

Installing Cement Backerboard

Installing Landscape Timber Edging

Installing Plastic Edging

Installing Metal Edging

Installing Wood Edging

Installing Sawtooth Brick Edging

Installing Flat Brick Edging

Installing Precast Concrete Edging

Installing Gutter Liners

Installing a New Flush Valve

Installing A Plunger-Valve Ballcock

Installing a Water Purifier

Installing A New Faucet

Installing a Toilet

Installing a Closet-Organizer System

Installing Stationary Brackets

Installing Adjustable Brackets

Installing Beaded-Board Wainscoting

Laying Out the Tiles

Laying Out Square Corners

Laying Out Arcs

Laying Out Straight Edges

Laying Out Free-form Curves

Maintaining Garage Door Openers

Making Minor Adjustments

Masking Wood Trim

Mitering Border Corners

Maintaining Your Storm Doors

Painting Flat Doors

Painting a Door (While Attached)

Painting a Door (Unattached)

Painting Trim

Painting Window Frames

Painting Exterior Windows

Painting Soffits and Fascia

Painting Jambs, Casings, and Trim

Patching Peeling Paint

Patching Large Holes in Wallboard

Patching Small Holes in Wallboard

Patching a Screen

Replacing Hinges

Replacing Door Pulls

Refinishing a Redwood or Cedar Deck

Renewing Your Deck

Refinishing a Pressure-Treated Deck

Replacing a Step

Repairing Decking and Joists

Replacing a Stair Railing

Replacing a Deck Railing

Roll-Up Door Maintenance Tips

Recessed Lighting

Replacing a Wall Switch

Removing Ceramic Tile

Removing Carpet

Removing Wood Flooring

Removing and Replacing Thresholds

Replacing a Threshold

Replacing Worn Valve Seats

Resurfacing Valve Seats

Repairing Leaky Downspout Joints

Repairing Leaky Metal Gutters

Replacing a Sink Sprayer

Removing Old Faucets

Removing a Toilet

 
| Site Map Site Map2 | Privacy Policy | © 2008 Handyman.PainterClick.com. All Rights Reserved.